logic symbol enecl enttl d0 d1 d2 d3 d4 d5 d6 d7 d8 q0 q1 q2 q3 q4 q5 q6 q7 q8 ttl ecl
semiconductor technical data 2140 rev 5 ? motorola, inc. 1996 3/93
the mc10h/100h600 is a 9bit, dual supply ttl to ecl translator. devices in the motorola 9bit translator series utilize the 28lead plcc for optimal power pinning, signal flowthrough and electrical performance. the h600 features both ecl and ttl logic enable controls for maximum flexibility. the 10h version is compatible with mecl 10h ecl logic levels. the 100h version is compatible with 100k levels. ? 9bit ideal for byteparity applications ? flowthrough configuration ? extra ttl and ecl power/ground pins to minimize switching noise ? ecl and ttl enable inputs ? dual supply ? 3.5 ns max d to q ? pnp ttl inputs for low loading ? choice of ecl compatibility: mecl 10h (10hxxx) or 100k (100hxxx)
fn suffix plastic package case 77602 pinout: 28lead plcc (top view) pin names pin function gnd v cce v cco v cct v ee d0 d8 q0 q8 enecl enttl ttl ground (0 v) ecl v cc (0 v) ecl v cc (0 v) e outputs ttl supply (+ 5.0 v) ecl supply ( 5.2 / 4.5 v) data inputs (ttl) data outputs (ecl) enable control (ecl) enable control (ttl) d6 5678 91011 25 24 23 22 21 20 19 d7 d8 gnd enttl nc enecl v cce q0 q1 v cco q2 v cco q3 26 27 28 2 3 4 18 17 16 14 13 12 15 d5 d4 v cct d3 d2 d1 d0 q8 q7 v cco q6 v ee q5 q4 enecl h h x x l enttl x x h h l d h l h l x q h l h l l truth table
mc10h600 MC100H600 2141 motorola mecl data dl122 e rev 6 dc characteristics: v cct = 5.0 v 10%; v ee = 5.2 v 5% (10h version); v ee = 4.2 v to 5.5 v (100h version) sbl p 0 c 25 c 75 c ui cdii symbol parameter min max min max min max unit condition power supply current i ee ecl 10h 100h 125 122 125 123 125 132 ma i cch i ccl ttl 48 50 48 50 48 50 ma ac characteristics: v cct = 5.0 v 10%; v ee = 5.2 v 5% (10h version); v ee = 4.2 v to 5.5 v (100h version) sbl p 0 c 25 c 75 c ui cdii symbol parameter min max min max min max unit condition t plh t propagation delay tootpt d 1.4 3.0 1.5 3.2 1.7 3.5 ns 50 w to 2.0 v t phl to output enecl / enttl 1.8 3.7 1.9 3.9 2.0 4.1 ns 50 w to 2.0 v t r t f output rise/fall time 20% 80% 0.5 1.5 0.5 1.5 0.5 1.5 ns 50 w to 2.0 v 10h ecl dc characteristics: v cct = 5.0 v 10%; v ee = 5.2 v 5% sbl p 0 c 25 c 75 c ui cdii symbol parameter min max min max min max unit condition i ih i il input high current input low current 0.5 225 0.5 145 0.5 145 m a m a v ih v il input high voltage input low voltage 1170 1950 840 1480 1130 1950 810 1480 1070 1950 735 1450 mv v oh v ol output high voltage output low voltage 1020 1950 840 1630 980 1950 810 1630 920 1950 735 1600 mv 50 w to 2.0 v 100h ecl dc characteristics: v cct = 5.0 v 10%; v ee = 4.2 v to 5.5 v sbl p 0 c 25 c 75 c ui cdii symbol parameter min max min max min max unit condition i ih i il input high current input low current 0.5 225 0.5 145 0.5 145 m a m a v ih v il input high voltage input low voltage 1165 1810 880 1475 1165 1810 880 1475 1165 1810 880 1475 mv v oh v ol output high voltage output low voltage 1025 1810 880 1620 1025 1810 880 1620 1025 1810 880 1620 mv 50 w to 2.0 v ttl dc characteristics: v cct = 5.0 v 10%; v ee = 5.2 v 5% (10h version); v ee = 4.2 v to 5.5 v (100h version) sbl p 0 c 25 c 75 c ui cdii symbol parameter min max min max min max unit condition v ih v il input high voltage input low voltage 2.0 0.8 2.0 0.8 2.0 0.8 v v i ih input high current 20 100 20 100 20 100 m a v in = 2.7 v v in = 7.0 v i il input low current 0.6 0.6 0.6 ma v in = 0.5 v v ik input clamp voltage 1.2 1.2 1.2 v i in = 18 ma
mc10h600 MC100H600 motorola mecl data dl122 e rev 6 2142 outline dimensions fn suffix plastic plcc package case 77602 issue d notes: 1. datums l, m, and n determined where top of lead shoulder exits plastic body at mold parting line. 2. dimension g1, true position to be measured at datum t, seating plane. 3. dimensions r and u do not include mold flash. allowable mold flash is 0.010 (0.250) per side. 4. dimensioning and tolerancing per ansi y14.5m, 1982. 5. controlling dimension: inch. 6. the package top may be smaller than the package bottom by up to 0.012 (0.300). dimensions r and u are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 7. dimension h does not include dambar protrusion or intrusion. the dambar protrusion(s) shall not cause the h dimension to be greater than 0.037 (0.940). the dambar intrusion(s) shall not cause the h dimension to be smaller than 0.025 (0.635). n m l v w d d y brk 28 1 view s s lm s 0.010 (0.250) n s t s lm m 0.007 (0.180) n s t 0.004 (0.100) g1 g j c z r e a seating plane s lm m 0.007 (0.180) n s t t b s lm s 0.010 (0.250) n s t s lm m 0.007 (0.180) n s t u s lm m 0.007 (0.180) n s t z g1 x view dd s lm m 0.007 (0.180) n s t k1 view s h k f s lm m 0.007 (0.180) n s t dim min max min max millimeters inches a 0.485 0.495 12.32 12.57 b 0.485 0.495 12.32 12.57 c 0.165 0.180 4.20 4.57 e 0.090 0.110 2.29 2.79 f 0.013 0.019 0.33 0.48 g 0.050 bsc 1.27 bsc h 0.026 0.032 0.66 0.81 j 0.020 0.51 k 0.025 0.64 r 0.450 0.456 11.43 11.58 u 0.450 0.456 11.43 11.58 v 0.042 0.048 1.07 1.21 w 0.042 0.048 1.07 1.21 x 0.042 0.056 1.07 1.42 y 0.020 0.50 z 2 10 2 10 g1 0.410 0.430 10.42 10.92 k1 0.040 1.02
mc10h600 MC100H600 2143 motorola mecl data dl122 e rev 6 motorola reserves the right to make changes without further notice to any products herein. motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. atypicalo parameters which may be provided in motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. motorola does not convey any license under its patent rights nor the rights of others. motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the motorola product could create a situation where personal injury or death may occur. should buyer purchase or use motorola products for any such unintended or unauthorized application, buyer shall indemnify and hold motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that motorola was negligent regarding the design or manufacture of the part. motorola and are registered trademarks of motorola, inc. motorola, inc. is an equal opportunity/affirmative action employer. how to reach us: usa / europe / locations not listed : motorola literature distribution; japan : nippon motorola ltd.; tatsumispdjldc, 6f seibubutsuryucenter, p.o. box 20912; phoenix, arizona 85036. 18004412447 or 6023035454 3142 tatsumi kotoku, tokyo 135, japan. 038135218315 mfax : rmfax0@email.sps.mot.com t ouchtone 6022446609 asia / pacific : motorola semiconductors h.k. ltd.; 8b tai ping industrial park, internet : http://designnet.com 51 ting kok r oad, tai po, n.t., hong kong. 85226629298 mc10h600/d ?
|
